Due to the COVID 19 epidemic, orders may be processed with a slight delay

Search

In Stock

MQ-9 Module (Methane & CO Gas Sensor)

Specifications:

  1. Good sensitivity to CO/Combustible Gas
  2. High sensitivity to Methane, Propane, and CO
  3. Long life and low cost
  4. Simple drive circuit
  5. Input voltage: DC 5±0.2V
  6. Current Consumption: 150mA

159.30

Compare
SKU:cds-s-g-mq-9

This is MQ-9 Carbon Monoxide, Methane, and LPG Gas Sensor Module can be used to sense Carbon Monoxide and Methane Gas. Sensitive material of MQ-9 gas sensor is SnO2, which with lower conductivity in clean air.It makes detection by the method of cycle high and low temperature, and detect CO when the low temperature (heated by 1.5V). The sensor’s conductivity is higher along with the gas concentration rising.When high temperature (heated by 5.0V), it detects Methane, Propane etc. combustible gas and cleans the other gases adsorbed under low temperature.

Wire Connections

VCC – Positive pole (5V)
GND – Negative pole
DO – TTL switch signal output
AO – Analog signal output

Reviews

There are no reviews yet.

Write a review

Your email address will not be published. Required fields are marked *

Bestsellers

Compare

MQ-135 Module (Ammonia, Sulphide and Benzene Gas Sensor)

159.30
(0 Reviews)
Specifications:
  1. Sensitivity to Ammonia, Sulphide and Benzene steam
  2. Sensitive for benzene, alcohol, smoke
  3. Fast response and recovery
  4. Adjustable sensitivity
  5. Signal output indicator
  6. Output voltage boosts along with the concentration of the measured gases increases
Compare

PM2.5 GP2Y1010AU0F Dust Smoke Particle Sensor

494.42
(0 Reviews)
Features:
  1. Power supply voltage: DC5 ± 2V
  2. Sensitivity: 0.5V / (0.1mg / m3)
  3. The minimum detection level of particles: 0.8 m
  4. Clean air voltage: 0.9V typ.
  5. Low consumption current (Icc: MAX. 20 mA)
  6. The presence of dust can be detected by the photometry of only one pulse
  7. Enable to distinguish smoke from house dust
Compare

MQ-2 Modules

149.86
(0 Reviews)
Specifications : 1. Good sensitivity to Combustible gas in a wide range 2. High sensitivity to LPG, Propane, and Hydrogen 3. Long life and low cost 4. Simple drive circuit 5. Can be used as a Digital or analog sensor 6. The Sensitivity of Digital pin can be varied using the potentiometer 7. Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO and even methan
Compare

MQ-3 Module (Alcohol Gas Sensor)

159.30
(0 Reviews)
Secifications:
  1. Sensitive to alcohol, ethanol
  2. Fast response and recovery
  3. Adjustable sensitivity
  4. Signal output indicator
  5. Analog and level signal output.
  6. The carbon monoxide detection with better sensitivity.
  7. Has a long service life and reliable stability.
  8. Output voltage boosts along with the concentration of the measured gases increases
Compare

MQ-4 Module (Methane ,CNG Gas Sensor)

149.86
(0 Reviews)
Secifications: 1. Detecting range: 300~10000ppm 2. Signal output indicator 3. Dual Signals output (analog output and TTL output) 4. TTL output signal is low level, allows to connect with SCM directly 5. Analog output 0~5V voltage 6. High sensitivity 7. Long working lifetime and stable performance 8. Quick response and recovery
Compare

MQ-5 Module (LPG Gas Sensor)

149.86
(0 Reviews)
Specifications : 1. High sensitivity to LPG, natural gas, town gas. 2. Small sensitivity to alcohol, smoke. 3. Stable and long life. 4. Simple drive circuit. 5. Fast response.
Compare

MQ-6 Module (LPG, Ethenol steam, Smoke Interference)

149.86
(0 Reviews)
Secifications:
  1. Operating Voltage: 5V DC
  2. Indication of the signal output
  3. Dual signal output (analog output, and TTL level output)
  4. 0 ~ 5V analog output voltage, the higher the concentration, the higher the voltage
  5. High sensitivity to hydrogen
  6. Can be resistant to ethanol steam, LPG (petroleum), smoke interference
  7. Has a long life and reliable stability
  8. Fast response and recovery characteristics

Back to Top
Product has been added to your cart