Showing 13–24 of 41 results
Compare
4 Channel 12V Optocoupler Based Relay Module
₹199.42(0 Reviews)
Features :
- This Board can be used to Control Solenoids, Motors, Lamps, etc,
- Input Logic: 12v level from MUC
- Indication LEDs for relay output status.• 12V 4-Channel relay board controlled directly by micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) need 50-60mA driver current
- Input IN1, IN2, IN3, IN4 signal line active low, 4-channel relay output module, relay output contact is maximum 250A 10A
- Input Pin connected to Burg stick. High-current, AC250V 10A, DC30V 10A.
Compare
4 Channel 5V Relay Module with Opto-Coupler
₹177.00(0 Reviews)
Features
- One normally closed contact and one normally open contact
- Channel: 4 channel
- Relay Operating Voltage: 3.3V to 5V
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, disconnect is off;
- Input signal, signal, common Terminal and start conducting;
- Useful for appliance control;
- DC or AC signal, control, you can control the 220V AC load;
- There is a normally open and one normally close contact;
- The module is compliant with international safety standards, control and load areas isolation trenches.
Compare
5V 1 Channel G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse
₹236.00(0 Reviews)
Specifications:
- It can be controlled directly by a Microcontroller
- Operating Voltage: 5V
- Operating Current: 12.5mA
- Maximum Load: 2A @ 240VAC
- Input control signal voltage:
- 0-2.5V status low level, relay OFF
- 3-5V status high level, relay ON
Compare
5V 1 Channel Relay Module (with Optocoupler)
₹89.68(0 Reviews)
Features
- Operating Voltage(VDC) : 5V
- Max. Current(mA) : 0.20 mA
- Current Capacity : 10A
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
Compare
5V 1 Channel Relay Module (with Optocoupler)
₹89.68(0 Reviews)
Features
- Operating Voltage(VDC) : 5V
- Max. Current(mA) : 0.20 mA
- Current Capacity : 10A
- Standard TTL Level logic controlled (AVR, Arduino, 8051, PIC, ARM)
Compare
5V 2 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse
₹289.10(0 Reviews)
Features:
- 2 channel 2 AMP Solid State Relay board
- Control 2 loads of up to 2 amps each at 120V or 240V AC.
- Good for lighting, holiday displays etc.
- Input control signal voltage:
- 0-0.5V the state of low-level relay ON
- 0.5-3.3V Unknown State
- 3.3-5V high-level relay OFF
- Operating Voltage: 5V
- Operating Current: 16mA
- Maximum Load: 2A @ 240VAC
Compare
5V 4 Channel SSR Solid State Relay Module 240V 2A Output with Resistive Fuse
₹558.14(0 Reviews)
Features :
- Operating Voltage: 5V
- Operating Current: 12.5mA
- Maximum Load: 2A @ 240VAC
- Led indicator for each relay.
- Use it to control various appliances and other equipment with large current.
- It can be controlled directly by Microcontroller
- Input control signal voltage:
- 0-2.5V status low level, relay OFF
- 3-5V status high level, relay ON
Compare
5V Relay (2 Pieces)
₹47.20(0 Reviews)
Features:
- Trigger Voltage (Voltage across coil) : 5V DC
- Trigger Current (Nominal current) : 70mA
- Maximum AC load current: 10A @ 250/125V AC
- Maximum DC load current: 10A @ 30/28V DC
- Compact 5-pin configuration with plastic moulding
- Operating time: 10msec Release time: 5msec
- Maximum switching: 300 operating/minute (mechanically)
Compare
6-30V 1-Channel Power Relay Module with Adjustable Timing Cycle
₹299.72(0 Reviews)
Specifications:
- Operating voltage: 6-30V
- Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable.
- Trigger Signal Source: High-Level Trigger (3.0 V-24 V)
- Output Capacity: can control no more than DC 30V 5A AC or 220 V devices 5A
- Optocoupler Isolation.
Compare
8 Channel 12V Optocoupler Based Relay Module
₹400.02(0 Reviews)
Features:
- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- A freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED status indicators to indicate the relay ON/OFF status
- Mounting holes provided
Compare
8 Channel 5V Relay Module Opto-Coupler
₹448.40(0 Reviews)
Features
-
- 5V 8-Channel Relay interface board
- LOW level trigger, equipped with indicator easy to recognize the working status
- Each relay has NO and NC ports, easier to connect and control the connected devices
- Selection of plastic material for high temperature and better chemical solution performance.
- PCB size: 5.7 x 13.8 cm
- Support control of 10A 30V DC and 10A 250V AC signals
Compare
BattleSwitch radio controlled 10A relay (Dimension Engineering)
₹1,984.00(0 Reviews)
Specifications:
- Max relay voltage: 240VAC
- Max relay current: 10A @ 28VDC, 12A @ 120VAC, 10A @ 240VAC.
- Relay resistance: 100 mΩ max
- 3.5V to 5.5V operating voltage (on servo pigtail)
- 30mA typical draw from receiver
