Programmers / Interface Modules(43)

Overview: Cytron has created this UIC-A so that users can use any programmer regardless of the development board. For example, a development board that uses PICkit2?s socket standard, which is 6-way header pins can be programmed with UIC000B by using the UIC-A!

Features: Processor: Cortex-M4 (up to 120MHz frequency) Ethernet: RJ45 (10/100Mbps self-negotiation) Protocols:IP, TCP, UDP, ARP, ICMP, DHCP, DNS, HTTPD Client Working Modes:TCP Server, TCP Client, UDP Server, UDP Client, HTTPD Client Interface Protection:Reverse-proof, ESD protection, anti-surge Storage temperature: -40~105C Power supply: 5.0~36.0V (5V recommended) Operating current: 86.5mA (@5V) Power consumption: <1W Dimensions: 82.8mm ? 85.7mm ? 25mm Operating temperature: -40~85C

Features : Operating voltage: 5V On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. All pins of the chip have been lead to can be controlled through the microcontroller. Convenient RS-485 communication wiring Multiple Units can be connected to the same RS-485 bus wiring.

Features : Input Supply voltage: 5V Input Supply Current: 5 mA Communication Rate: 1 Mbps Support CAN V2.0B technical standard, communication rate 1Mb / S. 0 to 8 bytes long data field. Use High-speed CAN transceiver TJA1050 SPI control for expanding Multi CAN bus interface Use serial port could view the communication data With the independent key, LED indicator, Power indicator With power pin Positioning screw hole center spacing 23 mm x 38 mm The working current: typical 5mA, standby current 1 microamp. Except for the power indicator.

Features: Direct plug design, works with most USB port and USB extension cable Low power consumption design Onboard 2?3 Pin AVR ISP port 3pin servo connector can be used as servo or C2 connection Supports SIMONK and BLHELI ESC, KKflashtool compatible KKflashtool and RapidFlash compatible Silabs CP2102 Driver chip! (Win, Mac, Linux) Software upgradeable (via Arduino or BLHELISUIT) Pre-load as BLHELISUIT 4w-if 14.1 firmware

Specifications: 8-Bit I/O Expander For I2C-Bus PCF8574 On Board

Specification : USB (Full speed 12 Mbits / s interface to host PC) Real-time execution MPLAB IDE compatible (free download from Microchip) built-in over-voltage / short circuit monitor Firmware upgradeable from PC / web download totally enclosed Diagnostic LEDs (power, busy, error) read/write program and data memory from a microcontroller erase program memory with Verification Freeze peripherals at a breakpoint program up to 512K byte flash with the Programmer to Go ICSP cable included

Features :

• Adopt imported controller PL2303HX, which can stabilize the flash with high speed
• 500mA self-recovery fuse for protection.
• Two data transmission indicator can monitor data transfer status in real time.
• Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power.
• The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside.
• The electrostatic package ensures the board will not be damaged before use. Support WIN7 system.

Specifications:

1. Input Supply voltage: 3.3.~ 5 V
2. Connector type: USB To TTL RS232
3. Cable length: 80 Cm
4. Supports RS-232 serial interface with Programmable baud rate from 75 bps to 12 Mbps
5. Compatible with the RS422/RS485 interface
6. The cables provide a fast, simple way to connect devices with a TTL level serial interface to USB
7. It is USB 2.0 full speed compatible. The USB side of the cable is USB powered.

Specifications:

1. IC Chip: MAX3232
2. Operating Voltage: 3.3-5.5V
3. Operates up to 250 kbit/s
4. Power supply: external
5. interface: TXD, RXD, GND, VCC
6. Dimensions: 33mm*32mm*16mm

Specifications:

1. IC Chip: MAX3232
2. Operating Voltage: 3.3-5.5V
3. It can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU
4. Pre-assembled compact size board
5. Suitable for use with most microcontrollers
6. Operates up to 250 kbit/s